EX-SW-0201-4K 1.png
EX-SW-0201-4K 2.png
EX-SW-0201-4K 3.png
EX-SW-0201-4K 4.png
EX-SW-0201-4K 5.png

HDBaseT™ VGA/HDMI Extender Set with Ethernet, Bidirectional IR, RS-232 and 2-Way PoH (4K: 100m/328ft | 1080p: 150m/492ft)

EX-SW-0201-4K

Supporting resolutions up to 4K, this fully-featured Class A HDBaseT extender is designed for use in small meeting room or classroom environments where distribution and control of VGA or HDMI devices up to 100m/328ft is required.


cat6_4k100_2k150.png

Overview

Dual-input Transmitter

Whether it’s a classroom or meeting room, you can never be too sure what devices will turn up. That’s why we’ve included VGA+audio and HDMI connections on this transmitter, it’ll also auto-switch between them should both need to be connected simultaneously.

Faultless Class A HDBaseT™ Transmission

Proudly flying the flag for the full ClassA HDBaseT™ feature set, the EX-SW-0201-4K levels-up, supporting not only 4Kvideo (HDMI input only), HD Audio and control but also allowing Ethernet pass-through and 2-way PoH meaning the extender can be powered from a single PSU, located at either end.

Audio de-embed on receiver

Meeting spaces don’t usually have the audio systems capable of handling HDMI connectivity, once connected to the screen, the signal is often terminated. We’ve included an audio output on the receiver of this extender to feed a simple stereo audio signal to a local audio system if sound reinforcement is required.

Flexible install options with 2-Way PoH

No 2 installs are the same, that’s why we’ve enabled all of the H2 extender line up to be powered from either the TX or RX side.

Features

  • A full-featured HDBaseT™ extender set with the added feature of a VGA/HDMI auto-switching transmitter
  • Transmit HD resolutions up to 1920x1200 to 100m/328ft
  • Transmit 4K@60Hz (4096x2160) to 70m/230ft
  • HDCP 2.2 compliant
  • 3D supported
  • Auto-switching transmitter detects and selects VGA (+audio) and HDMI devices as soon as the source is connected
  • 2-way PoH gives flexible installation options by allowing either the transmitter or receiver to be powered remotely
  • Audio embed on transmitter and audio de-embed on receiver via 3.5mm jack connection for HDMI or VGA
  • EDID management and DIP switch selection for manual setting of resolution, RS-232 control/firmware update function and long cable mode
  • Low-profile 18mm chassis for unobtrusive installation
  • Cable termination follows IEEE-568B standards
  • LED indication for power supply to units, signal status to show established display connection, HDCP presence in signal and transmission link.
  • Threaded bushings allow use of both standard and locking DC power plugs
  • Energy efficient universal power supply included
  • Mounting brackets included

Specifications

Audio and Video

Transmitter
Receiver
Inputs 1x HDMI 19-pin type A
1x VGA In 15-pin VGA VESA (D-SUB 15)
1x Audio In 3.5mm (1/8in) Stereo Jack
1x HDBaseT™ 8-pin RJ-45 female
Outputs 1x HDBaseT 8-pin RJ-45 female
1x HDMI 19-pin type A female
1x Audio Out 3.5 (1/8in) Stereo Jack
Audio Formats 2ch PCM | Up to 7.1 DTS-X and Dolby Atmos
Video Resolutions (Max) Video Resolutions
1920x1200p @60Hz 16bit
3840x2160p @30Hz 8bit 4:4:4
4096x2160p @60Hz 8bit 4:2:0
HDMI
15m/49ft
7m/23ft
7m/23ft
Cat6
70m/230ft
70m/230ft
70m/230ft
Cat6a/7
100m/328ft
100m/328ft
100m/328ft
Supported Standards DCI
Maximum Pixel Clock 297mHz

Communication and Control

HDMI HDCP 2.2 Compliant | EDID | DVI/D supported with adapter (not included)
HDBaseT™ HDCP 2.2 Compliant | EDID | 2-way PoH | Bidirectional IR and RS-232
RS-232 1x 3-pin Screw Down Phoenix Connector | Bidirectional over HDBaseT™
IR 1x IR TX 3.5mm (1/8in) Mono | Bidirectional over HDBaseT™
1x IR RX 3.5mm (1/8in) Stereo | Bidirectional over HDBaseT™
Ethernet 1x 8-pin RJ-45 female | 10/100 Mbps auto-negotiating

Power

Power Supply Input: 100~240V AC 50/60Hz | Output: 12V DC 2A
Max Power Consumption 26.5W
PoH 48V 15.4W

Environmental

Operating Temperature 32°F ~ 113°F (0°C ~ 45°C) | 10% ~ 90%, non-condensing
Storage Temperature -4°F to ~ 158°F (-20°C ~ +70°C) | 10% ~ 90%, non-condensing
Maximum BTU 90.42

Dimensions & Weight

Rack Units/Wall Box 1U
Height 20mm/0.79in
Width 200mm/7.88in
Depth 134mm/5.28in
Weight 0.6kg/1.32lbs

Regulatory

Safety and Emission CE | FCC | RoHS

Case Studies