NHD-100-TX.png
NHD-100-TX 2.png
NHD-100-TX 3.png

NetworkHD™ 100 Series AV over IP H.264 Encoder

NHD-100-TX

The NHD-100-TX is the source device encoder for the NetworkHD™ 100 Series, an ultra low bandwidth H.264 AV over IP solution for distribution of point-to-point, one-to-many and many-to-many AV distribution over a managed network. With its standards-based approach to video encoding, simple system configuration and robust feature set, it provides the best value in networked video distribution.

The NHD-100-TX H.264 encoder is intended for use with an NHD-100-RX H.264 decoder (sold separately) to provide a complete end-to-end video distribution system. It is also compatible with the NHD-000-CTL system controller, NHD-220-RX multiview decoder.


eth_2k100.png

Overview

Highly Scalable

Powered by H.264 encoding for a high quality, low bandwidth AVoIP solution, the cross-compatible NetworkHD 100 and 200 Series modular system architecture removes the limitations of traditional fixed platform matrix systems, whilst offering significant cost savings for large scale deployments.

Powerful Video Processing

Dynamic video processing seamlessly converts and matches source video content from each decoder to connected displays, removing video resolution and timing incompatibilities that might otherwise exist for reliable and easily manageable multi-display systems.

Serial & HDMI Device Control

In addition to HDMI streaming over an IP Network, the 100 Series sends RS-232 control signals to a source or display and CEC control commands to a display device for single control signal deployment without the need for additional equipment.

QuickSync™ Seamless Switching

WyreStorm’s QuickSync technology offers virtually instantaneous, seamless source switching free of glitches or tears between video streams for an enhanced user experience worthy of any professional video distribution installation.

Features

  • For use with the NHD-100-RX H.264 decoder to provide a complete end-to-end streaming system
  • NetworkHD Touch™ iPad control app for live video previews and drag and drop source selection
  • Features 1x HDMI input to 1x LAN (PoE) output
  • Provides a scalable Multicast video stream output via Ethernet port
  • Supports input signal resolution up to 1920 x 1200@60Hz
  • Highly scalable, high quality, low bandwidth solution using the most efficient compression technologies to allow for very large commercial AV deployments
  • Plug and Play setup with quick networking configuration and auto discovery of components
  • Major control systems drivers available including the WyreStorm Enado™ Control System
  • Supports secondary video preview stream for PC or third party user interface
  • Compatible with the NHD-000-CTL for matrix control and management via the LAN, as well as for allowing control from third party control system such as AMX, Crestron, Control4, RTI & Enado
  • Supports PoE to be remotely powered from the switch by compatible power source equipment, eliminating the need for a nearby power outlet
  • Standards-based H.264/MPEG-4 AVC video compression
  • Full PC control suite available free of charge at wyrestorm.com
  • Supports HDCP
  • Configurable encoding bit rate up to 30Mbps

Specifications

Audio and Video

Inputs 1x HDMI In 19-pin HDMI type A female
Outputs 1x LAN (PoE) 8-pin RJ-45 female | 10/100Base-T
1x Audio Out: 3-pin Phoenix
Audio Formats 2ch PCM
Output Video Encoding H.264/MPEG-4 AVC
Video Resolutions (Max) Note: Interlaced content at any resolution is not supported, all source content must be progressive.
HDMI: 1920x1080p @60Hz 8bit (15m/50ft)
Cat6/6a/7: 1920x1080p @60Hz 8bit (100m/328ft Point to Point)
Encoding Data Rate 2~30Mb/s
End to End Latency 60~90 ms (Low latency mode) | 250~300 ms (High quality mode)
Color Depth 8bit
Maximum Pixel Clock 150MHz

Communication and Control

HDMI HDMI | HDCP 1.4
Ethernet
1x 8-pin RJ-45 female | 10/100Base-T | PoE
RS-232 1x RS-232: 3-pin Phoenix

Power

Power Supply 12V DC 1A
PoE IEEE 802.3af | 12V 1A 12.95W
Max Power Consumption 6W (DC adapter)

Environmental

Operating Temperature 32°F ~ 113°F (0°C ~ 45°C)
10% ~ 90%, non-condensing
StorageTemperature -4°F to ~ 158°F (-20°C ~ +70°C)
10% ~ 90%, non-condensing
Maximum BTU 20.47 BTU/hr

Dimensions & Weight

Rack Units/Wall Box <1U
Height 25mm/0.98in
Width 200mm/7.87
Depth 94mm/3.7in
Weight 0.6kg/1.32lbs

Regulatory

Safety and Emission CE | FCC | RoHS

Accessories

What’s included? 1x NHD-100-RX
1x 12v DC 1A. Power Supply
3x 3-pin Phoenix Connector
2x Mounting Ears
1x Quickstart Guide

Case Studies